Home > Raid 1 > RAID 1 Not Recognized In WinXP Setup

RAID 1 Not Recognized In WinXP Setup

Thank you for posting this! Choose your device from the list. If you're new to Tech Support Guy, we highly recommend that you visit our Guide for New Members. But this dose not seem to be the case? http://olivettipc.com/raid-1/raid-1-question.html

I have downloaded the drivers from the HP website and extracted, and the procedure to use the nlite is very confusing. by ComputerCookie ยท 9 years ago In reply to OK got her all to work NE ... It automatically went into a chkdsk screen, and took over 20 minutes "recovering orphaned files." My feeling is that this drive may be seriously corrupted. At a loss here.

Last modified: July 9, 2012 Hard Disk Gone Missing? besure your hard drives were well ventilated. 0 Cook Back to top #3 hamluis hamluis Senior TEG Forum Member Members 4,199 posts Gender:Male Location:Killeen, TX Interests:Sports, reading, physical well-being, computers, music, Reply Sandi L.

but my older hdd still undetectable in bios also.plz plz help me i have imp data on it Reply Trish says: December 17, 2011 at 07:24 Thanks! I find alright but they disappear on the main page and only the IDE and empty sata drive indexes are visible. Reply Venkat.G says: September 23, 2012 at 22:54 Thank you for the help!! Please can> someone advise:>> I had a single 160gb maxtor HDD system that I converted from Basic to> Dynamic (for some reason;)) I then purchased an identical drive, and> connected it

any solution Reply trips says: July 13, 2012 at 09:29 you're excellent, the best and thank you very much Reply Md says: July 14, 2012 at 16:33 I tried The Way My system came up with the error "NTLDR missing" I did some settings in BIOS couldn't resolve the issue, Also tried to reinstall windows XP but HDD was been recognised in thanks!!!!!!!!!!!!!!!!! The process is explained in detail in this article. 6.

i have 2 HDs 1Tr & 75 GB. Reply Ken says: November 10, 2009 at 03:05 Again, I really need help. Who are these "Han Solo" actors? Your first fix worked like a charm.

Reply yk says: May 13, 2011 at 19:33 Rosco, thank you for trying to help. In my case I had type the following command. % ntfsfix isw Notice the "isw" when I was discussing the desktop icons. By viewing our content, you are accepting the use of cookies. I wonder why it says secondary drive because its the only drive i have. (1 hard disk with no partition, yes all the data is only in C drive (i didn't

You were a very big help!!!! :* Reply Jason says: August 6, 2011 at 21:14 Hi, I have a compaq nc6320, and window setup could not find hard drive either with click site First solution worked 100%!!!! What is AHCI/RAID drivers? There are a few ways to deal with this ranging from the very simple (hopefully says you!) to the long and somewhat difficult.

Reply Syed says: September 30, 2012 at 13:41 Great(: it solved the problem Thanks Reply Dennis says: September 15, 2014 at 03:51 Disabling the SATA allowed me to continue Windows XP Typically, there is no need to change these, other than a couple of places. now i get another error …. http://olivettipc.com/raid-1/raid-1-0-calculator.html When I boot to the XP CD, it goes through the "Checking Configuration" screen for a few minutes, and then tells me that there is no Hard Drive in the system.

R. I then disconnected all drives except the raided drives which contain my active partition with OS, but still no change - WinXP will not boot up. Wait for process completion.

Take an image (I like Clonezilla) of the working disk and image it to a network drive or other location.

The problem is that it appears that my floppy drive is not working, because it is not even turning and trying to read the floppy when I press enter... Have you tried resetting the BIOS jumper (and, of course, setting the correct boot order)? I know this may be the beginning of the end, and I'll watch for it - but at this point both drives are working. Reply Abbas says: September 30, 2013 at 15:18 Thanks a lot dude, just disabled the native sata support n setup has initiated, I spent about good few hours to figure out

Keep up the good work … Reply kasaye says: May 7, 2012 at 05:56 i would like to …. I am taking the opportunity to save some files to an external drive (even though I have most important files already backed-up), but I don't know where to go from here. I am not finding the serial SATA option in BIOS setup of Server 7800 series. http://olivettipc.com/raid-1/raid-1-questions.html So if it has bno Bage saying what version it is you have 32 Bit Software.

If so is there a quick fix so that I can get my system back up?FYII have tried to slave the disks in another machine, however cannot access the drives, something Phoenix Bios version 35.02.01. I thought 2 dives in a raid 1 should pick up either one. He came over and thanked me for what I'd done, and also asked me about pay it forward.

For that reason, Windows must load Text Mode Drivers from floppy. R. What do you reckon? I dont have any other controllers apart from the standard MB one. > 2) From the RAID BIOS (not sure how to get into it on that board, F4 > sounds

My PM8 recovery disk running in DOS does NOT have the chkdsk option from the main menu (partition drop down submenu offers windows checkdisk from within the version running in windows Louis 0 Back to top #6 bamboku bamboku Junior TEG Forum Member Members 1 posts Posted 28 September 2008 - 03:51 PM great! Reply Rosco says: September 23, 2010 at 09:27 Hi Nhikol…DBAN wipes hard disks so it's likely that you'll get this error after using DBAN. p.s.

Any ideas of where to go from here? But would it greatly change my laptop by disabling the SATA? Thanks again Reply joseph jp says: March 18, 2013 at 02:18 yoooohhh man your great.. Is it safe for me to try the solution?