Home > Problems With > "the Volume Bitmap Is Incorrect"

"the Volume Bitmap Is Incorrect"


serious. This condition may occur if other processes are using a very large amount of system resources. however, if it's too complicated, i'll happily just take it as is. Action To reconnect inode inode-number to the file system in the lost+found directory, type y.

not sure what to do, hopefully I posted this correctly this time! CHKDSK is verifying security descriptors (stage 3 of 3)... This message does not display if the file system is being preened because lack of space to reconnect files terminates fsck. You might get lucky.

"the Volume Bitmap Is Incorrect"

Running CHKDSK in read-only mode. Can't open filename Cause fsck cannot open file system filename. Not necessarily concerned. To terminate the program, type n.

Is this something I need to be concerned about? For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. It said my drive is in use, so I should do that after restart. Chkdsk /f Other benefits of registering an account are subscribing to topics and forums, creating a blog, and having no ads shown anywhere on the site.

If the recheck fails, contact your local service provider or another qualified person. Chkdsk Spotfix Action To allocate inode 2 as the root inode, type y at the ALLOCATE prompt. Action To delete the extraneous entry hard-link-number type y at the REMOVE prompt. This is a community maintained site.

same as Error Checking, ticking only the upper box.chkdsk /r ..... Any advice please? After the restart I logged on and ran another chkdsk using command prompt and here are the results: 9/3/2013 8:34pm Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. Cleaning up 11 unused security descritors.

Chkdsk Spotfix

F parameter not specified. For more serious conditions, the command reports the error and terminates. "the Volume Bitmap Is Incorrect" Odds are all is not lost; you may be able to create a gpt partition table, with your >2T partition starting in exactly the same place as before, but ending at Windows Cannot Run Disk Checking On This Volume Because It Is Write Protected To ignore the error condition, type n.

If the directory is successfully reconnected, a CONNECTED message is displayed. I initially thought the problem was caused from the pc slowing down before I lost an internet connection but that isn't the prob now. fsck exits. Compare what you see when the analysis is finished, to what you see when the defrag is complete.Let me know how it goes. Chkdsk Command

  • and others.
  • Staff Online Now Triple6 Moderator valis Moderator davehc Trusted Advisor flavallee Trusted Advisor Macboatmaster Trusted Advisor TheShooter93 Malware Specialist Advertisement Tech Support Guy Home Forums > Operating Systems > Windows XP
  • More resources Tom's Hardware Around the World Tom's Hardware Around the World Denmark Norway Finland Russia France Turkey Germany UK Italy USA Subscribe to Tom's Hardware Search the site Ok About
  • When running interactively, fsck ignores this file system and continues checking the next file system given.
  • Figured maybe there was a disk or file system problem, so I ran chkdsk in the read-only mode.
  • lolalola View Public Profile Send a private message to lolalola Find all posts by lolalola #2 05-06-16, 14:14 Cantrel Top contributor Join Date: Jul 2012 Location: UK Posts:
  • Windows keeps "meta-data" about each file and every directory on your hard drive in a Master File Table (MFT).Meta-data is data about the data.
  • Free space verification is complete. 976760000 KB total disk space. 217232812 KB in 202941 files. 89272 KB in 11813 indexes. 0 KB in bad sectors. 406248 KB in use by the
  • a7xcoreya7z BSOD, App Crashes And Hangs 5 05-23-2011 07:11 PM Fake Windows Security Program has infected my computer!

mishamisha Virus/Trojan/Spyware Help 26 07-14-2011 07:36 PM .exe problems, and possible Malware issues Aloha, Need help... TerryNet, Sep 4, 2013 #2 psylock Thread Starter Joined: Dec 19, 2012 Messages: 166 OK, I'll just keep running chkdsk and chkdsk /f, thank you. Action Contact your local service provider or another qualified person. Please help, thank you!!

Action To deallocate the inode inode-number by zeroing out its contents, type y. If another allocated inode with a zero-link count is found, this error condition repeats. Please help me remove it!

fsck cannot resolve this problem.

Everything was fine until I rebooted; now I can't mount! drive has errors rma/or replace it no errors run chkdsk /p in recovery console and see if that doesn't correct the drive errors. Advertisement Recent Posts Please help me hard reset! It can be but if you have tried other disks then run this MS Fixit to see if it will do anything for you - I assume you are still using

block-number DUP I=inode-number Cause Inode inode-number contains a block number block-number, which is already claimed by the same or another inode. Type n to terminate the program. Index verification completed. AnonymousMay 4, 2005, 11:11 AM Archived from groups: microsoft.public.windowsxp.perform_maintain (More info?)I've been having problems getting Firefox to load consistently, especially a second or third time.

Short URL to this thread: https://techguy.org/1107615 Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account? Action To remove the directory entry filename, type y at the REMOVE prompt. You can read about what MyDefrag attempts to do at the following web page:http://www.mydefrag.com/You said: "could you explain what these log "issues" are?"I will attempt a very brief explanation ... To ignore this error condition, type n.

CHKDSK is verifying indexes (stage 2 of 3)... I cannot access the internet or anything else. However, for more serious errors, the command reports the inconsistency and prompts you to choose a response. To ignore this error condition, type n.

Take these disk check results as a friendly reminder. If/when I finally get a Win 10 laptop, I doubt I'll be using Cortana which will save me from having to create a MS account and that I will still be Please re-enable javascript to access full functionality. Before the file system check can be performed, fsck sets up tables and opens files.

Phase 1: Check Blocks and Sizes Messages This phase checks the inode list. When confronted with such a message, terminate the program by entering n(o). Phase 3: Check Connectivity Messages This phase checks the directories examined in phase 2 and reports error conditions resulting from: Unreferenced directories Missing or full lost+found directories These messages (in alphabetical Action If this message is displayed, contact your local service provider or another qualified person.

Then it choked and said it couldn't continue in read-only mode.> > > > So I ran chkdsk /F again, got a clean report, then ran chkdsk again in > > Get the answer AnonymousMay 6, 2005, 5:33 AM Archived from groups: microsoft.public.windowsxp.perform_maintain (More info?)"Cleveland Mike" wrote:>I have indeed run chkdsk /R several times, but the results have not changed. >I CHKDSK is verifying file data (stage 4 of 5)... Edited by AustrAlien, 01 February 2011 - 07:37 PM.