Home > Hard Drive > Hard Drive And Dvd On Same Ide Cable

Hard Drive And Dvd On Same Ide Cable

Contents

There are SATA 4 ports though that are associated w/NV raid and I am not hooked up to them so i don't think it makes a difference. Since this particular computer does not have a floppy drive, is there any other way to install a SATA HDD driver? How do I configure an MSI z170A PC Mate to recognize a CD/DVD Writer as the initial boot disk? what i have to buy? navigate here

It's set that way by default.If it's possible someone has set bios settings wrong, load bios defaults, save bios settings, then look in the bios again to see if the SATA when I enter setup (bios) I cant see my hdd. I try press F8 but won't start to the save mode, its restart again and again. Using an ide to sata convertor(extension) on this drive it would not fit in the case.So I intend to fit both ide hdd's to the ide connector jumpered master and slave

Hard Drive And Dvd On Same Ide Cable

The only setting in bios that I saw having to do with the controller was the RAID controller. About 10 days ago I started having trouble similar to yours where the storage HDDs weren't being recognised by the BIOS or my Linux OS. The hard drive that has a bootable partition must be made to be first in the list, Save bios settings.- or - you must change which data header the drive that If you own a quality torque screwdriver, it can't hurt to start on the lowest torque setting and see if some of the screws turn at low torques while others are

  • From research that I've done on the internet and because the computer is running Win XP, it seems that a driver for the SATA HDD must be installed.
  • When the PC powers up, you should hear the hard drive motor spinning up the drive and the gentle clunking sound of the read/write head seeking.
  • i need to connect it with my laptop.
  • In terms of cabling issues for power and data, and jumpers for addressing, troubleshooting SSD drives when they are interfaced as PATA or SATA drives is the same as for the
  • Also, refer to the Service Manual for accurate steps and safety instructions.
  • Return to Diagnostic Chart Does the drive cycle up and down?
  • This was done approximately two years ago and, until now, there have been no further problems.
  • This is the workstation: Windows 8.1 x64 AMD Athlon x64 x2 5200+ 2.7GHz 4GB DDR2 RAM NG1DB-M25 Biostar motherboard 1TB Western Digital HDD DVD Drive (not sure brand) As you can

If neither fix helps, try disconnecting the data cable to ensure that the drive isn't receiving some flaky power down signal from a bad ATA interface or a crazy power management The bios WILL NOT try to boot from another hard drive if the first one it detects is NOT bootable. It looks to me like the spring action of the clip pushes the contacts away from each other; over time, with heat, this could cause intermittent disconnects. –boot13 May 7 '15 How To Connect Dvd Drive To Motherboard Sata Common keys used to access CMOS Setup at boot are, , and .

Remove the CD-ROM from adapter and connect to DVD burner. Back to top #9 DaChew DaChew Visiting Alien BC Advisor 10,317 posts OFFLINE Gender:Male Location:millenium falcon and rockytop Local time:12:06 PM Posted 11 January 2008 - 12:15 PM I am In that case, you need to- go into the bios and find the list of hard drives. To run PSA, press and hold the `Fn' key on the keyboard and then press the power button to start the computer.

Not the answer you're looking for? Ide To Sata Converter Remove the CD-ROM from adapter and connect to DVD burner. If you're just looking for faster boot time, a SATA 3 SSD may make more sense. Before taking the PC to my local computer guy I thought I'd try one last thing.

How Many Hard Drives Can Be Connected To A Single Ide Cable

Just power down, put the drive back in and continue with the diagnostics. If still not detected, Hard Drive needs to be replaced. * 4. Hard Drive And Dvd On Same Ide Cable If the motherboard won't register any drive you attach, even on new cables, and if those drives are spinning up, it indicates that either the IDE controller is bad or all Sata Power Cable Multiple Connectors Should we always specify ID attribute in HTML?

Two years ago, I installed Windows XP on both this computer as well as my wife's SR5050NX and did not encounter this problem at that time. http://olivettipc.com/hard-drive/rip-dvd-to-hard-drive.html Return to Diagnostic Chart Is the SSD drive equipped with a SATA or PATA (IDE) interface? but when I tried ACHI it does not detect my hdd. Motherboard Specifications, P5LP-LE (Leonite)http://h10025.www1.hp.com/ewfrf/wc/...Ewen said..."Sorry... Ide Hard Drive Jumper Settings

The boot drive (WDC5000AAKS) is on controller #1. Report • #6 Tubesandwires May 15, 2012 at 12:05:29 Thanks for the Many thanksWe're glad to hear you solved your problem. Report [email protected] Oct 22, 2013 at 01:45 AM thanks you very much Boss Report sp- Nov 25, 2013 at 03:08 AM thanks...good article... http://olivettipc.com/hard-drive/2tb-hard-drive-ps3.html Ask !

Your cache administrator is webmaster. Sata Cable The signals would get confused, and chaos would ensue. Test and did not work.2).

Helpful +7 Report Zohaib R 2402Posts Sunday September 23, 2012Registration date June 16, 2016 Last seen Mar 7, 2013 at 01:04 PM Hi firewolf123, Please keep us updated with the status

If you do get a message warning of impending drive failure from the operating system or from the motherboard BIOS, it pays to back up your data and just replace the Can't find your answer ? Was it the kind with clips? Get the answer manan purohitJun 16, 2015, 5:56 AM but how to connect power adapter molex i mean how to use it and connect to get sata cable.

On the SATA drives, the power cable is wider than the data cable, on the older PATA or IDE drives, the data cable is a wide ribbon cable and the power Try not. Any suggestions on how to solve this problem? weblink Do reply with results.

How can i connect 3 internal hard drives and 1 dvd writer in my pc solved Connecting a Laptop Hard disk directly to Desktop (SATA) Connecting DVD SATA powered to 2nd The unending soft clicks are caused by the read/write head arm jerking back and forth in a series of seeks as it tries to read data from the platter. If system restore fails or unable to access safe mode, follow next step. 6. anyway I decided to run super fdisk to correct my partion table.